Controlled Power & Lighting Inc. handles urgent electrical problems for homes and businesses in Sebastian, FL, including sudden power loss, breakers that will not stay on, burning smells, sparking outlets, and damage after a storm or surge. This page is for property owners who think something in their wiring, panel, or fixtures has gone wrong and needs a licensed electrical contractor to look at it. To get started, call or send a request that describes what you saw, heard, or smelled.

Maybe the lights dimmed and half the house went dark. Maybe an outlet is warm to the touch, a breaker snaps back off the moment you reset it, or there is a faint smell of hot plastic near the panel. Those are not problems to wait out. The most helpful thing you can do right now is make the area safe, note the details, and get someone qualified to trace the cause instead of guessing at it.


Warning Signs to Act On

Some electrical symptoms are a nuisance. Others mean heat is building somewhere it should not be. These are the ones we hear about most often from Sebastian customers:

  • Burning or fishy smell near an outlet, switch, light fixture, or the electrical panel.
  • Breaker that trips again right away after you reset it, or one that feels hot or will not stay in the on position.
  • Sparking or buzzing from an outlet, a plug, or inside the panel cover.
  • Scorch marks or discolored cover plates around outlets and switches.
  • Lights that flicker or dim when an appliance starts, or an entire circuit that suddenly goes dead.
  • Partial power loss where some rooms work and others do not, even though the utility power is on.
  • Mild shocks when you touch an appliance, a metal plate, or a switch.
  • Storm or surge damage such as dead electronics, a fried outlet, or a service mast pulled loose.

Any one of these is worth a call. Two or three together usually point to a failing connection, an overloaded circuit, or a damaged panel component that needs hands-on testing.


What to Do First

While you wait for an electrician, a few calm steps reduce risk. If you see flames or someone has been hurt, call 911 before anything else.

  1. Stay clear of water. Do not touch the panel, outlets, or cords if the floor is wet or the area has taken on water.
  2. Switch off the affected circuit. If the breaker is accessible and dry, turn off the one that serves the problem area. Leave the main breaker alone unless the situation is getting worse and you can reach it safely.
  3. Unplug what you can. Pull plugs from the dead or warm outlet and from nearby devices, but only if the outlet is not sparking or hot enough to hurt.
  4. Do not keep resetting. A breaker that trips is doing its job. Forcing it back on over and over can overheat wiring.
  5. Write down what happened. Note what was running, when it started, any sounds or smells, and which rooms are affected. This shortens the troubleshooting.

Storm and Coastal Causes

Sebastian sits on Florida's east coast, and most of the year the weather is hard on electrical systems. Summer thunderstorms bring lightning and voltage spikes. Humidity and salt air tend to corrode connections over time, especially at outdoor outlets, meter bases, disconnects, and exterior lights. Hurricane season adds the risk of wind-driven rain getting into fixtures and panels, plus the surges that often come when utility power drops out and returns.

Age matters too. Many homes across Sebastian, Vero Beach, Fellsmere, Micco, and the surrounding area have gone through years of added appliances, window units, pool equipment, and workshop tools on circuits that were laid out for lighter loads. When a breaker finally fails or a connection overheats, it is often the end of a slow build-up rather than a random event.


Repair or Upgrade?

Homeowners often wonder whether an urgent call turns into a bigger project. Usually the first job is to find the fault and make the circuit safe. That might be replacing a worn breaker, repairing a burned receptacle, correcting a loose connection, or tracing a short. This page covers that urgent troubleshooting and repair work.

A panel upgrade is a different job. If the visit shows a panel that is damaged, overloaded, or no longer suited to the equipment on it, we can explain the findings and talk through whether a panel replacement or service upgrade makes sense. That is planned work with its own scope and quote, so you are never pushed into it in the middle of a stressful night. Surge protection is also a separate conversation, one worth having if lightning damage is what brought you here.


How a Visit Goes

Every job is different, but urgent electrical calls tend to follow the same general path:

  1. Listen and gather details. The electrician asks what you noticed, what was running, and what has been tried already.
  2. Make it safe. Affected circuits are isolated so the problem is not left energized while it is being diagnosed.
  3. Test and trace. Breakers, outlets, switches, connections, and the panel are checked until the actual cause is found, not just the symptom.
  4. Explain the options. You should hear what failed, what it will take to fix, and whether anything else nearby looks worn or unsafe.
  5. Repair and confirm. After the repair, the circuit is tested and power is restored to the affected areas.

Controlled Power & Lighting Inc. serves both residential and commercial customers, so the same approach applies whether the trouble is in a kitchen, a garage, or a small business space.


What Good Work Looks Like

You do not need to be an electrician to judge a repair. Hold any provider to these standards:

  • Find the cause. Swapping a breaker without asking why it tripped is a guess. Good work includes tracing the fault.
  • Match the parts to the circuit. Breaker size, wire gauge, and device ratings should fit the load, not just fit the slot.
  • Tight, clean connections. Loose or scorched terminations are a common cause of repeat failures and should be corrected, not covered up.
  • Clear explanation. You should be told what was found, what was changed, and what to watch for afterward.
  • Tidy finish. Panel covers back on, damaged devices removed, and the work area left clean.

Questions to Ask First

Whether you call us or anyone else in the Sebastian area, ask these before work begins:

  • Do you hold the Florida electrical contractor license that applies to this work, and can I see the number?
  • Do you carry liability insurance, and will it cover my property while you work?
  • What exactly is included in the quote: diagnosis, parts, labor, and cleanup?
  • Will this repair need a permit or inspection, and who handles that?
  • How will you let me know if you find something beyond the original problem before doing extra work?
  • When can you realistically arrive, and how will you update me if that changes?

What Affects the Cost

Urgent electrical work is priced by what is actually wrong, so two similar-sounding calls can look very different on paper. The main factors are:

  • How long it takes to locate the fault, especially if it is hidden in a wall, attic, or underground run.
  • Which parts are needed, such as a breaker, receptacle, switch, fixture, or a section of wiring.
  • Whether the panel itself is damaged or outdated and affects the repair.
  • Access to the work area, including height, tight spaces, and outdoor exposure.
  • Whether code requirements call for a permit or additional corrections once the work is opened up.
  • Storm or surge damage that spreads across several circuits or devices.

A clear written quote should spell out the scope of the repair, what is covered by the labor and what is parts, any extras you have approved, and how changes will be handled if more work turns up. If the scope grows, you should be told and asked before anything is added.


Common Questions

Is It Safe to Keep Resetting a Breaker That Keeps Tripping?

No. A breaker that trips repeatedly is telling you there is an overload, a short, or a failing component. Resetting it over and over can overheat wires. Leave that circuit off and have it tested.

Can an Outlet Be Dangerous Even If It Looks Fine?

Yes. Heat damage often starts behind the cover plate at a loose connection. A warm outlet, a faint burning smell, or a plug that feels loose are good reasons to stop using it and have it checked.

What Should I Do After a Lightning Strike or Power Surge?

Check for smells, scorch marks, or dead outlets, and unplug sensitive electronics. If anything seems off, have the panel and affected circuits tested. Damage from a surge is not always visible right away.

How Is the Price for an Urgent Repair Worked Out?

It depends on the time needed to find the fault, the parts required, access to the work area, and whether the panel or wiring needs more than a simple fix. A written quote should break these out.

Will a Repair Turn into a Panel Replacement?

Not usually. Many problems come down to a single breaker, device, or connection. If testing shows a damaged or overloaded panel, we will explain what we found and discuss upgrade options as a separate decision.

What Should I Tell You When I Call or Send a Request?

Share your location in the Sebastian area, what you noticed, which rooms are affected, what was running when it started, and whether any breaker has tripped. Photos of the panel or damaged outlet help too.

Have an Electrical Project? Let’s Talk.

Tell us what you need, from a flickering light to a full panel upgrade, and we’ll get back to you with a clear next step.